Skip to content

pwmarcz/fpga-chip8

Repository files navigation

CHIP-8 console on FPGA

This a CHIP-8 game console emulator working on FPGA chip (TinyFPGA BX).

invaders invaders2-small

Implementation notes and remarks

Writing unit tests (see cpu, gpu, bcd) helped me a lot, I was able to test most instructions in simulation. I wrote several simple assembly programs which I compiled to CHIP-8 using the Tortilla-8 project.

There was also some manual testing needed in order to get both the screen and the keypad to work. I wrote some simple programs to run on the chip, and corrected some misconceptions I have on CHIP-8 behavior (for instance, memory loads and stores include multiple registers, and sprite drawing wraps around). I was able to correct my Rust CHIP-8 emulator in the process; it's funny how it was able to run many games despite getting these things completely wrong.

The CHIP-8 specification includes 16 one-byte registers (V0 to VF) and 20 two-byte words of stack. Initially I wanted them to be separate arrays, but it was really hard to coordinate access so that they get synthesized as RAM, so I decided to map them to memory instead (see the memory map described at the top of cpu.v).

I also mapped screen contents to system memory, so two different modules (CPU and screen) had to compete for memory access somehow. I decided to pause the CPU (i.e. not make it process the next instruction) whenever we want to read the screen contents.

Working with screen was annoying. I'm storing the frame contents line by line (each byte is an 8-pixel horizontal strip), but the screen I'm using expects vertical strips of 8 pixels, so there's some logic necessary for rotating that around.

The BCD instruction (convert a byte to 3 decimal digits) was difficult to implement in circuitry since it involves diving by 10. I went with a method described in Hacker's Delight, which involves some bit shifts and a manual adjustments. See bcd.v.

Loading games into memory was interesting. The IceStorm tools include a nice icebram utility for replacing memory contents in an already prepared bitstream. This means I don't have to repeat the whole lengthy (~30s) build when I just want to run a different game.

The default clock speed on the BX is 16 MHz, which is way too fast for CHIP-8 games. So while the individual instructions run really quickly, I throttle down the overall speed to 500 instructions per second.

I added a "debug mode" that activates when you press 1 and F at the same time. Instead of showing the screen buffer, I'm rendering registers, stack and (some of) program memory instead. It's fun to watch :)

Random number generation uses Xorshift. It calculates a new value every cycle, and iterates the calculation twice if any key is pressed so that the results depend on user input.

Finally, I'm very new to Verilog and so the project is somewhat awkward:

  • An individual instruction takes about 20 cycles.
  • Memory access follows a "read -> acknowledge" cycle with an unnecessary single-cycle pause due to how the state automatons are specified.
  • iCE40 memory is dual port, so reads and writes could happen at the same time; I'm not taking advantage of that.
  • The whole project takes up 1600+ LUTs, I'm sure it could be packed down to less than 1000, then it could fit on an iCEstick.

I would love to hear from you if you have any advice on the code - just email me or add an issue to the project. Of course, pull requests are also welcome!

Hardware

I'm using the following:

Source code outline

Verilog modules:

  • chip8.v - top-level module for TinyFPGA BX
  • cpu.v - CPU with memory controller
  • mem.v - system memory
  • gpu.v - sprite drawing
  • bcd.v - BCD conversion circuit (byte to 3 decimal digits)
  • rng.v - pseudorandom number generator
  • screen_bridge.v - bridge between OLED and CPU (to access frame buffer in system memory)

Tests:

  • *_tb.v - test-benches for modules (see below on how to run)
  • asm/ - various assembly programs

Games:

The fpga-tools repo is included as a submodule:

  • fpga.mk - Makefile targets
  • components/oled.v - OLED screen
  • components/keypad.v - keypad

Running the project

See INSTALL.md.

License

By Paweł Marczewski pwmarcz@gmail.com.

Licensed under MIT (see LICENSE), except the games directory.

See also

Releases

No releases published

Packages

No packages published